Hot Sale Boilers
GET 20%OFF √
Certification:ASME、ISO9001、CE、ISO、BV、CCC
Available fuel:Nature gas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available industries:Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
E-mail:[email protected]
Please email or call us for your inquiry
2008/1/1 · A lack of balance can cause excessive steam-outlet velocity, resulting in an extremely volatile water surface and failure of a level-control system. The maximum velocity of steam through a header under full-load conditions should be 50 fps.
Get priceThe mechanics of the natural convection circulation of boiler water within the steam generator is the origin of the dynamic shrink/swell phenomenon. Consider what happens to a boiler operating at steady state at 600 psig when it is subjected to a sudden increase in load (or steam demand).
Get price2018/6/8 · Boiler types : According to usage • Hot water boiler • Thermal oil boiler • Steam boiler • Steam generator • Exhaust gas boiler. 20. Hot water boiler: Hot water boilers are normally used in room and building heating. These kinds of systems are …
Get priceColder feedwater in the steam drum replaces the water that rises, thus creating a natural circulation of water. Low-water level conditions have the potential to severely damage the boiler. The furnace temperatures usually exceed 1,800°F (980°C) and the only thing that allows a boiler to withstand these furnace temperatures is the presence of water in all tubes of the furnace at …
Get priceC. water tight door D. all the above Answer-D 15. Function of a de-superheater is to A. Protect superheater from overheat B. Control superheater steam outlet temperature C. Increase the efficiency of the boiler D. Reduce steam temperature for auxiliary uses
Get price4. The fluid heater/steam generator must be properly vented in accordance with national fuel gas code and local codes. Serious property damage could result if the steam generator ventilation requirements are not adhered to. 5. It is the responsibility of the
Get priceIn some steam drum designs, water level is extremely critical because the baffling may isolate a generating section of the boiler when the steam drum water level falls below a certain point. Thin-lipped bursts also occur in superheater tubes when steam flow is insufficient, when deposits restrict flow, or when tubes are blocked by water due to a rapid firing rate during boiler start-up.
Get priceHow to Destroy a Boiler -- Part 1 William L. Reeves, P.E President, ESI Inc. of Tennessee Category: Incidents Summary: The following article is a part of the National Board Technical Series. This article was originally published in the Winter 1999 National Board BULLETIN..
Get priceThe test is achieved by lowering the float to the low water alarm level, by the following means: The float rod includes a cup above the float, which is fed for approximately 24 seconds with water from the boiler feedpump, via small bore pipework and valves, through the control mounting flange (see Figure 3.19.6).
Get price1. (PG60.1) All boilers having a fixed water level (steam and water interface) shall have at least one gage glass (a transparent device that permits visual determination of the water level). 2. (PG‐60.1.1) Boilers having a maximum allowable working pressure
Get pricefuel used, are driven by steam generated in a boiler. The boiler heats water and converts it to steam, spinning the turbine and in turn, driving the generator that produces electrical power. After exiting the turbine, the steam is routed through a condenser, cooling
Get price1. (PG60.1) All boilers having a fixed water level (steam and water interface) shall have at least one gage glass (a transparent device that permits visual determination of the water level). 2. (PG‐60.1.1) Boilers having a maximum allowable working pressure
Get priceColder feedwater in the steam drum replaces the water that rises, thus creating a natural circulation of water. Low-water level conditions have the potential to severely damage the boiler. The furnace temperatures usually exceed 1,800°F (980°C) and the only thing that allows a boiler to withstand these furnace temperatures is the presence of water in all tubes of the furnace at …
Get priceThe mechanics of the natural convection circulation of boiler water within the steam generator is the origin of the dynamic shrink/swell phenomenon. Consider what happens to a boiler operating at steady state at 600 psig when it is subjected to a sudden increase in load (or steam demand).
Get priceWater Level Alarms Where boilers are operated without constant supervision (which includes the majority of industrial boilers) low water level alarms are required to shut down the boiler in the event of a lack of water in the boiler. Low level may be caused by: A
Get price